KAB BATTERY BOARD
KAB BATTERY BOARD
KAB BATTERY BOARD
KAB BATTERY BOARD
KAB BATTERY BOARD

KAB BATTERY BOARD

BUILT IN LI-ION CHARGER SUITS KAB SERIES

Li-Ion battery charging board for three 18650 batteries . Recommended BAT-KAB sold separately. Fully protected for safe charging of unprotected batteries. 19Vdc 4A power adaptor is required.

  • The Dayton Audio KAB-BE Li-Ion battery charging board holds three 18650 batteries (sold separately). This charging board has built in under/over voltage protection circuits for safe charging and battery longevity. It balances different voltages between batteries in case one battery discharges faster than the other ones. A 19Vdc 4A - 5A power adaptor works best for charging batteries contained in this board. Additional boards can be sequenced together to provide longer playing time.

    • Under/over voltage protection prevents over charging the batteries
    • Voltage balancing keeps the sound playing even if one of the batteries is weaker than the others
    • Holds three 18650 Li-Ion batteries (sold separately)
    • Built-in 20cm 4 conductor cable plugs

    • When changing batteries for the KAB-BE, the charging adapter must be plugged in momentarily after the new batteries have been inserted. Failing to do so will prevent the amp board from powering up. Note: Standard 18650 batteries dont fit this charger. Requires BAT-KAB batteries only. Read / Show More

    Found in Category : HiFi Equipment

    KAB-BE - BATTERY EXTENSION BOARD

    $21.50

    Order Code: KAB-BE
    Availability : In Stock
    Product Details
    Add To Cart
    Order Code KAB-BE
    Related Products
    BATTERIES TO SUIT KAB-BE

    BATTERIES TO SUIT KAB-BE

    A standard 18650 battery with inbuilt protection circuit does not fit in the KAB-BE charger. The BAT-KAB battery does not have the circuit and so is marginally smaller and fits fine. The KAB-BE has the protection circuit to maintain safe operation. Please only use BAT-KAB with the KAB-BE charger.

    BAT-KAB - BATTERY SUIT KAB-BE ONLY

    $12.95

    Order Code: BAT-KAB
    Availability : In Stock
    Product Details
    Add To Cart
    Order Code BAT-KAB
    POWER SUPPLY RECOMMENDED FOR KAB-BE

    POWER SUPPLY RECOMMENDED FOR KAB-BE

    SUGGESTED POWER PACK CONNECTION: KAB-BE power equirements were tested to find that 19V power source with a high available current rating and inbuilt over-current protection was required to charge these large capacity Li-Ion cells.* Note: Testing here found that some power supply solutions were not compatible with the KAB-BE charging circuit and/or the circuits built inside some Li-Ion cells. In particular we found charging power demands were quite high and that lower current power supplies caused protection circuit issues.* CONSTRUCTION: Solder the MTB832 to the available solder terminals on the KAB-BE board Connect the DCL2119ST to the MTB832 observing polarity as indicated on the board: Red lead to positive, black to negative. Insert the three 18650 Li-Ion batteries (Supplied separately) Note: Battery insertion, depending on the cell, can be a bit tight. You may need to first adjust the height of the terminals to accept the RBLI series of cells as sold by WES. Connect the KAB-BE with the supplied header lead to the amplifier board as per the instructions supplied with KAB-230 or KAB-250. Adjust the SMP90W power supply voltage setting to 19V as recommended. Attach the 2.1mm DC plug option to the SMP90W and insert into DCL2119ST. You should now have a functioning power supply set-up. Status LEDs will light. This will both charge the batteries and also power the unit to around 40W total. Simply disconnect the SMP90W for battery operation, reconnect for recharging. DISCLAIMER: Other voltages and supplies can be used at the users discretion. Alternative setups are beyond the scope of this sheet and are at the risk of the user. *This is to be used as general guide only in response to some testing here at WES. This is by no means a comprehensive data set of available options for the KAB-BE as the constructor may connect various power options as they see fit, and as such, WES can not be held resposible for the users choice, circumstances or abilies. We strongly suggest further research when constructing your project. A good source of information is the PartsExpress website as it has a users Q&A: https://www.parts-express.com/Search.aspx?keyword=KAB-BE

    SMP-90W - SMP-90W POWER SUPPLY

    Bulk Buy: $64.64 for 10 or more

    $69.95

    Order Code: SMP-90W
    Availability : In Stock
    Product Details
    Add To Cart
    Order Code SMP-90W

    Contact us for Bulk Buy and Project Based Pricing for KAB BATTERY BOARD



    DescriptionFileSize
    Wiring Guide KAB-BE.pdf 20182 KB
    KAB-BE - Product Downloads

    Description File Size
    18650 Important Notice! BAT-KAB_Note.pdf 998 KB
    BAT-KAB - Product Downloads

    Description File Size
    Important Note! BAT-KAB_Note.pdf 998 KB

    Please contact us with your download requirements,e.g. User Manual, Data Sheet, etc and will get back to you.


    © 2015 Wagner Online Store. All Rights Reserved