Phone: 02-9798-9233 Fax: 02-9798-0017 Electronic Components 10-114 Amplifier Modules KAB KAB V4 2X 50W AMPLIFIER BOARD CLASS-D DIY WITH BLUETOOTH 5.0 The Dayton Audio KAB-250v4 Bluetooth Amplifier Board makes it quick and easy to add audio to your project, speaker build, point-of-purchase display, kiosk, or any location where music or sound enhances the experience. With an output of 2 x 50 watts, there is more than enough power to drive stereo speakers, yet the board is small enough to integrate into nearly any project. • High quality power from the efficient TPA3116 Class-D amplifier IC • Qualcomm Bluetooth 5.0 module Supports aptX HD, aptX LL, SBC and AAC. • On board external antenna jack enables mounting in a metal enclosure • Module includes power and speaker output wiring harnesses 50cm • Class-D 90% Efficiency plus very low standby power consumption • Direct DC input from a power adaptor 12Vdc / 24Vdc or • Power by battery or optional Li-Ion battery charger solution • Compact 91x69x23mm with built-in heat sink • 2x 50W 4 Ohm (21Vdc 5A) 92dB SNR 22Hz-22KHz • Optional accessories expand the functionality for your project Code KAB-250V4 KAB 2X 30W AMPLIFIER BOARD WITH DSP CLASS-D DIY WITH BLUETOOTH 5.0 aptX HD INBUILT SIGNAL PROCESSOR COMPATIBLE WITH KPX The Dayton Audio KAB-230v4 Bluetooth Amplifier Board makes it quick and easy to add audio to your project, speaker build, point-of-purchase display, kiosk, or any location where music or sound enhances the experience. With an output of 2 x 30 watts, there is more than enough power to drive stereo speakers, yet the board is small enough to integrate into nearly any project. • Efficient 2 x 30 watts of power from the TPA3118 amp chip • Bluetooth 5.0 with aptX HD built directly into board -- no need for a separate module • Add programmable sound customization with Dayton-Audio’s included KABX software via the optional KPX programmer board (sold separately) • Wire harnesses make installation quick and simple with no soldering required • Includes power and speaker cables to connector break-out leads • Separate ports for powering by battery or direct DC input from a power adaptor • Optional accessories expand functionality and more Code KAB-230V4 KAB 2X 30W AMPLIFIER BOARD WITH DSP CLASS-D DIY WITH BLUETOOTH 5.0 aptX HD Dayton Audio KABD-230 combines a 2 x 30W amp board, Bluetooth 5.0, and an ADAU1701 digital signal processor all in one amp board. This enables you to customize your next DIY audio project's sound using SigmaStudio software and Dayton Audio KPX or ICP1 Bluetooth programmer. Code KABD-230 KPX IN-CIRCUIT PROGRAMMER BOARD DAYTON AUDIO PROPRIETARY KABX SOFTWARE CONTROL The dual-purpose Dayton Audio KPX allows you to unlock the full potential of your DSPB/KABD amplifier or preamp boards by connecting them to the easy to use, Analog Devices SigmaStudio visual programming tool. KPX also enables you to use KABX software to preset equalisation settings and more for the KAB-250v4, KAB-230v4, and KAB-100Mv2. Code KPX HIGH DEFINITION BLUETOOTH - KPX & ICP1 COMPATIBLE • All-in-one board design reduces space needed for audio DIY projects. • Wire harnesses make installation quick and simple with no soldering required • Includes power, Bluetooth reset button and speaker cables. • Separate ports for powering by battery or DC input from 12 to 24V power source. • Integrated ADAU1701 DSP chip for ultimate signal control and customisation. • Program with SigmaStudio software using ICP1 or KPX boards (sold separately). • Class-D amplification with efficient 2 x 30W of power from the TPA3116 amp chip. • Easy to use plug-and-play solderless configuration for simple DIY projects. • DSP controlled line level output for connecting powered subwoofers or amplifiers. • Bluetooth 5.0 or line-level AUX input accommodates wireless and wired audio • Programs with readily available SigmaStudio or KABX computer software • Connects to your computer using a standard USB-C cable (sold separately) • 50 x 50 mm size fits into small enclosure projects for permanent installations or easy connection to your KABD/DSPB amplifier or preamp boards • Includes a 6-pin, 8" jumper cable that plugs directly into DSPB and KABD amplifier boards • Includes a 4-pin, 8" jumper cable that plugs directly into KAB-250v4, KAB-230v4, boards • Built-in switch toggles between the two software programs/ports DIY
RkJQdWJsaXNoZXIy NDQ2MDk=