Web: www.wagneronline.com.au Email: [email protected] Audio Speakers & PA 03-165 Impedance 4Ω (Re 3.4Ω) Fs 200Hz Sens. 77dB Power 5Wrms Qes 1.05 Qms 0.68 Qts 0.41 Vas 0.021L Code SB36WBAC21-4 SB ACOUSTICS 1" FULL RANGE - WBAC SUPER-COMPACT FULL RANGE ALUMINIUM CONE SB ACOUSTICS 2.5" FULL RANGE - WBAC FULL RANGE ALUMINIUM CONE Geometrically furrowed aluminium cone for extended usable frequency range. Copper cap for increased high frequency output, reduced phase shift at higher frequencies and improved power handling capability. Low damping surround and non-conductive voice coil former to ensure dynamics and an open/transparent sound character with excellent detailing/resolution. Linear neodymium motor system for reduced distortion. Vented voice coil former for reduced compression. Ø72.0 Ø6.5 (x4) 64.0 Ø3.3 (x4) R40.0 32.7 3.0 Ø 38.0 38 REV.2 (03.01.2014) (IEC baffle, mic.distance 31.6 cm, SPL shown for 2.83 V / 1 m) 100 95 90 85 80 75 70 65 60 55 50 45 40 82 75 69 62 55 49 42 35 29 22 15 9 2 Ohm dB 20 50 100 200 500 1k 2k 5k 10k 20kHz Response Curve : (Blue) : on axis (Green) : 30° off-axis ( Red ) : ------ ------ ------ 60° off-axis Long stroke low damping surround. Vented low compression design. Resonance and break-up control. Low resonance frequency. Prepared for rear mounting. Long life silver lead wires. Impedance 8Ω (Re 5.8Ω) Fs 160Hz Sens. 75dB Power 5Wrms Qes 0.92 Qms 1.75 Qts 0.61 Vas 0.035L Code SB36WBAC21-8 Ø43.0 Ø36.0 Ø34.0 3.0 6.5 11.0 10.6 20.8 17.9 2.5 REV.1 (21.07.2017) (IEC baffle, mic.distance 31.6 cm, SPL shown for 2.83 V / 1 m) 100 95 90 85 80 75 70 65 60 55 50 45 40 40.0 36.7 33.3 30.0 26.7 23.3 20.0 16.7 13.3 10.0 6.7 3.3 0.0 Ohm dB Response Curve : (Green) : 30° off-axis ( Red ) : 60° off-axis ------ (Blue) : on axis ------ ------ 20 50 100 200 500 1k 2k 5k 10k 20kHz Impedance 4Ω (Re 3.0Ω) Fs 115Hz Power 20Wrms Sens. 83.5dB Qes 0.77 Qms 6 Qts 0.68 Vas 0.43L Code SB65WBAC25-4 SB ACOUSTICS 3" FULL RANGE - PGC • Low damping surround and non-conductive • Voice coil former to ensure good dynamics • Transparent sound character with fine detail. • Vented voice coil for heat exchange and reduced compression. • Light weight CCAW voice coil. • Optimised fibre glass cone for smooth response. • Compact square chassis for versatile integration. Impedance 4Ω (Re 3.4Ω) Power 20Wrms Sens. 84dB Fs 89Hz Qms 11.2 Qes 1.01 Qts 0.92 Vas 1.2L Code SB10PGC21-4 Ø73.6 Ø55.0 77.4 44.2 50.8 Ø85.0±0.20 Ø95.5 Ø6.5(x4) Ø3.3(x4) 90° 45° 3.0 SB ACOUSTICS SPECIFICATIONS DATASHEETS ARE AVAILABLE • Datasheets Online: All data is as supplied by the manufacturer SB Acoustics at the time of print and believed to be accurate, however, specifications may change. Please see the website for the latest data sheets with additional data and information on specifications and parameters on each driver. • Thiele and Small Parameters: These specifications are given as a general guide to aid in comparison and selection of drivers only. Please consider that there are different methods in obtaining T/S parameters and that your results may vary. SBA uses the delta-mass method on broken-in drivers, see their website for details ("Tech.Notes"). SPL Sensitivity given is measured at 2.83V/1m. • Power Ratings given (where stated as Wrms) are according to SBA datasheets and specified as IEC 268-5. This is an 8 hour speaker stress test designed to emulate real-world audio conditions to accurately represent a long-term power specification and amplifier power recommendation. Power handling is a complex issue as conditions can vary considerably, but generally speaking, a loudspeaker rated at 50 watts by this testing method would have been stressed during its 8-hour test period by instantaneous power input of up to 200 watts. A speaker rated at 50 watts can be safely driven by an amplifier capable of 100 watts output without clipping and given the driver has ample thermal dispersion.
RkJQdWJsaXNoZXIy NDQ2MDk=